SSWS4.6 SOLDER SLEEVE WIRE SPLICES 5.0X4.6X40MM BLUE Radio Parts

Solder sleeve wire splice is a low-cost easy installation cable joiner. It consists of transparent heat shrinkable sleeve and fluxed solder that melts around the cable when heated up to provide insulation and make cable waterproof.Simply join two cables together and slide the middle of solder sleeve on the contact point. Use a heat gunto melt heat shrink and solder until it contacts closely with cable jacket.

• In-line wire splices
• Fully recovery temperature: 130°C
• Temperature of fully solder melt: 150°C

Model	Color	Before Shrinking(mm)		After Shrinking(mm)		Solder Ring			Total Length(mm)
		Gap	Shrink Thickness	Gap	Thickness	Gap	Thickness	Length
SSWS1.8	White	2.0±0.1	0.3±0.05	1.1±0.1	0.5±0.05	1.8±0.1	0.3±0.05	1.6±0.1	25±0.5
SSWS2.9	Red	3.2±0.2	0.38±0.05	1.5±0.1	0.55±0.05	2.9±0.1	0.45±0.05	3.0±0.1	40±0.5
SSWS4.6	Blue	5.0±0.2	0.4±0.05	2.6±0.1	0.78±0.05	4.6±0.1	0.48±0.05	4.2±0.1	40±0.5
SSWS6.2	Yellow	6.5±0.2	0.4±0.05	3.0±0.1	0.8±0.05	6.2±0.1	0.5±0.05	4.3±0.1	40±0.5

 

 

Example of solder sleeve to cable sizes(as 16/5/17):

Category	Type	Code	AWG	Solder sleeve	Marker
Data	Cat5e	05062805	24	SSWS1.8	White
Data	Cat6	05062825	23	SSWS1.8	White
Data	Cat6A	05062912	23	SSWS1.8	White
Intercom	KBwire	05061974	19	SSWS1.8	White
Security	4 core	05062008	7×0.2	SSWS1.8	White
Power	Figure8	05093003	24×0.2	SSWS2.9	Red
Speaker	41 strand	05101041	18	SSWS4.6	Blue
Speaker	Medium	05101090	16	SSWS2.9	Red
Speaker	Blustream	05107072	16	SSWS2.9	Red
Speaker	Medium	05101110	14	SSWS2.9	Red
Speaker	Heavy	05101150	12	SSWS4.6	Blue
Speaker	DOHQ	05109015	17	SSWS6.2	Yellow
Auto	4mm	05040379	26×0.3	SSWS4.6	Blue
Auto	6mm	05040390	10	SSWS4.6	Blue
Trailer	7 core	05041201	9×0.3	SSWS2.9	Red
Hook up	Thin	05081220	21×0.08	SSWS1.8	White
Hook up	Medium	05082020	7×0.25	SSWS1.8	White
Hook up	Thick	05084000	24×0.2	SSWS2.9	Red

Solder Sleeve Wire Splices Install Instruction

The easy to install and inspect, waterproof, single-piece Solder Sleeve Splice is the perfect solution in either an industrial setting or any home D.I.Y situation. Below is a basic step by step guide to solder two wires together, usingthe Solder Sleeve Splice and a heat gun, to create a solid and protected single connection.

1.  With the Solder Sleeve already on one of the wires, peel and expose each end of the two wires to a suitable length for joining.

2. Join both ends of the two exposed wires together, as pictured below, ensuring both ends are thoroughly connected.

3. Move the Solder Splice down the wire over the joining ends, making sure the solder centre of the sleeve covers the exposed joint, as pictured below.

4. Using a heat gun and starting from one end, heat the Solder Sleeve and slowly move along the splice till you have heat shrunk the entire length.

5. Be careful to heat shrink the whole Solder Sleeve without overheating it.

6. The finished Solder Sleeve should look like the completed wire splice pictured below.

Now you can enjoy your two joined wires, as a single, strong and waterproof cable.